7/15/2000 | 3 MINUTE READ

Hot Technology Key To Valve Maker's Success

Facebook Share Icon LinkedIn Share Icon Twitter Share Icon Share by EMail icon Print Icon

Rotary transfer machines do the trick for this valve maker.

Share

Facebook Share Icon LinkedIn Share Icon Twitter Share Icon Share by EMail icon Print Icon

Related Suppliers

Until 1991 or 1992, Lincoln Brass (Waynesboro, Tennessee) turned out valves and fittings primarily on screw machines and a battery of other machines for secondary drilling, milling, threading, finishing and so on. A typical scenario, manufacturing manager David Sharpe says, would be blanking out a part on a screw machine, sending it through two to ten secondary operations for completion, then taking these parts to assembly for valve completion.

"It was pretty difficult to manage," Mr. Sharpe says, "keeping track of what parts were at what stages in a given process, and changing over could take literally days—not that it takes that long to change over a screw machine, but when you factor in all the various secondary machines, you often were looking at days."

Lincoln Brass also has competitive pressure, both domestic and global, that it must deal with. The company uses a long-range strategy that involves investing in the best technology that will consistently address the value side of the value/cost ratio.

"Our strategy," Mr. Sharpe says, "is to buy for the long term. We don't believe in spending money for equipment that's going to need replacement every three or four years, even if that equipment costs significantly less. If we pay $300,000 to $1.3 million for a machine, we expect that machine to run 100 million cycles—or more."

So Mr. Sharpe looked at a variety of companies with these strategies in mind. What he found were Hydromat precision rotary transfer machines and Hydromat technology from Hydromat (St. Louis, Missouri).

Now, with a stable of Hydromats, Mr. Sharpe reports that the tracking difficulty has lessened. Parts that used to take two to ten steps now are down to a single machine setup. The effects on productivity, WIP, inventory, setup and part changeover have been dramatic. "Parts made this afternoon," he says, "will be on a truck bound for the customer by daylight. We've reduced total inventory by more than half, from $8 million to $3 million. By eliminating secondary operations, scrap has, for all practical purposes, disappeared. Setup times have gone from days to 15 minutes or an hour. When you run millions of parts a year, these kind of benefits are not only critical, but can keep you looking back, not ahead, to the competition."

A major strategic priority at Lincoln is the elimination of all secondary operations, says Mr. Sharpe. "An example of how the Hydromats contribute to this is a standard inverting unit. This removes a workpiece from a collet, turns it 180 degrees end--forend and then replaces it precisely back in the same collet. This way we can completely machine the back side of the component, which ordinarily would require a separate, secondary operation, involving another machine and another setup."

Mr. Sharpe suggests that the strength of precision rotary transfer machine technology is in its flexibility to do on a single machine that which traditionally requires several machines, multiple handlings and setups, a great deal of wasted time, loss of quality control and increased scrap.

"Drilling, milling, cross drilling, boring, turning, external and internal recessing, threading, tapping, broaching—these are all normal secondary operations," Mr. Sharpe says. "Doing all these on a single machine gets rid of waste—in time and scrap—and gives us control of our operations."

Further, Mr. Sharpe suggests there are certain operations that would simply be impossible, or at the very least extremely difficult, by any other approach. Drilling a diameter on an angle that must precisely meet with another diameter on the interior of a part, thus becoming an ellipse, is a real challenge using multiple setups, Mr. Sharpe says. "If the angles aren't absolutely precise, the ellipse becomes either too big or too small, and the result is a scrapped out part. However, the table indexing and repeatability are so consistently precise on the Hydromats that this kind of angular drilling isn't a concern."

"We run an average of 45,000 parts a day on some of the Hydromats," Mr. Sharpe says. "They consistently hold 0.0005 inch, day in, day out. We routinely produce surface finishes with an Ra of 6, which is smooth as glass. We annually produce some 12 million valves, and on average there are at least three Hydromat parts in each valve assembly—that's 36 million parts. And for our valves to continue to beat the competition, each of these parts has to be completely within tolerance, each assembly perfectly functional."

A lot has changed at Lincoln Brass in the last six or seven years. The company carries less than half the inventory it did only a short time ago, has dramatically cut work in process and almost entirely eliminated scrap. Product quality has consistently and reliably improved the company's standing in the valve business. MMS

Hand holding a crystal ball

We’d rather send you $15 than rely on our crystal ball…

It’s Capital Spending Survey season and the manufacturing industry is counting on you to participate! Odds are that you received our 5-minute Metalworking survey from Production Machining in your mail or email. Fill it out and we’ll email you $15 to exchange for your choice of gift card or charitable donation. Are you in the U.S. and not sure you received the survey? Contact us to access it.

Help us inform the industry and everybody benefits.

RELATED CONTENT

  • Gearing Up For High-Volume Automotive Parts

    CNC rotary transfer machines are helping this shop make the transition.

  • Rotary Transfer: Turning Up the Volume

    This contract manufacturer set its sights on high volume, precision turning and assembly of complex components from Day 1 and continues to succeed in a market many have abandoned using CNC rotary transfer machining.

  • Closing The CNC Price Gap

    Applying CNC technology to the manufacturing of precision parts is generally accepted as a premium that one must pay for the advantages over conventional actuation systems. Increasingly, however, the gap is narrowing as economies of scale for producing CNC equipped machine tools are incorporated in the unit price of a given machine. In other words, spreading the costs of manufacturing over a larger base of installations will reduce the price of each machine.


Resources